craftsman power washer how to start

Put the choke lever to Run. Now move the startup switch to the ON position.

Top Reasons Pressure Washer Soap Injector Isn T Working Pressure Washe Pressure Washer Repair Videos Repair Clinic

Craftsman Pressure Washer Model.

. Craftsman Pressure washer wont start 01 - Spark Plug. Now youre ready to start the pressure washer. It just needed a carb clean.

Set switch to 1 connected water line discharged air made sure there was a steady water stream left the spray trigger on while I pulled the starter. V20 Cordless Push-Button Battery-Start Pressure Washer Kit 3200 MAX PSI New. Cover bushes plants and flowers near your cleaning project to protect them from detergents.

How to start an electric pressure washer. 4 possible causes and potential solutions. Positioning is an extremely important parameter.

Make sure its tighter. 01 - Spark Plug. Move the engine throttle to full throttle position.

The end result is a carburetor that does not work and a pressure washer that does not start. As this is powered by a gas-powered engine there are a few steps you need to take each time you start your power washer. Left a little in over winter and filled with fresh.

This is the type with the B S engine that doesnt need to be primed or choked. This video will show the startup procedure for a gas powered pressure washer. Before you start your craftsman pressure washer.

Adjustable water pressures from 300 to 3300 PSI let you control pressure to reduce the chances of damaging surrounding materials. I changed the oil dumped the old fuel pulled off and cleaned the carburetor and installed a new spark plug. En español Live Chat online.

Adjust the flow of detergent through the siphon hose by turning the knob on the end of the siphon hose that attaches to the pressure washer. If the starter cord wont move when you try to start your power washer you may have a locked up engine or. Press and hold the trigger on the sprayer gun to clear any air or debris.

Inspect the spark plug for signs of wear or damage. Lightly place back the handle to the original position. PRESSURE WASHER viewing Download PDF.

You should see a strong spark between the testers. If you are using a gas powered washing unit fill the gas tank with gas. Showing 10 of 39 parts.

Up to 25 cash back My craftsman pressure washer model no--wthe gvc 160 Honda engine wont start. Next connect the male end of the high pressure hose that comes with the unit into the water. With that out of the way lets now go on to how to start Briggs and Stratton power washer.

Start by connecting your hose to the pressure washer. If you have an electric power washer this is when you will plug it in. You heard it right.

Make sure the pressure washer is on a flat surface and check to make sure the water strainer is in place and free of debris. How To Start Your Craftsman Power Washer. You should see two different options for how to connect it one is a quick disconnect and another might be labeled as an M22 connector or something similar.

Make sure that you have a female end on both ends of the hose. The solution to this is to use a carb cleaner or carburetor cleaning agent. The engine wont start if the engine is out of fuel or if the fuel is stale or contaminated with water.

Attaching hose to water supply. Tried with the spray trigger off. If the porcelain insulator is cracked an electrode is burned away or damaged or there is heavy carbon buildup at the electrode replace the spark plug.

Turn the water on and then turn the water valve open on the power washer. Screw the water hose onto the water connector at the base of the power washing unit. Turn the knob clockwise to decrease the soap solution concentration and counterclockwise to increase it.

I tried everything to get it started after being i. Flushing the carburetor out with a special cleaning agent should remove the heavy carbon buildup residue and allow the power washer to start. Pressure washer wont start.

Connect a garden hose to the washer and the other end to your water supply. Always place your pressure washer on a flat surface. Below is the step-by-step guide to starting your Craftsman gas-powered power washer.

We will also discuss some basic steps to guide you deeply. The next step is to attach the garden hose to the water supply. Attach one end of the pressure hose to the water pump of the washer and another end to the High-pressure spray gun.

To determine if the spark plug is defective use a spark plug tester. Turn the water supply on starting the flow of water into your washer. QUICK DIRTY cleaning the carburetor without taking it off the mowerI got this pressure washer free a couple of years ago.

CRAFTSMAN gas and electric pressure washers make sidewalks driveways decks and more look like new. So first things first heres a guide on starting your power washer. Move the choke to the open position.

Make sure its being placed on a levelled surface. Grip the starter handle and pull it slowly until you feel it getting heavy. Place the fuel valve to the open position.

Once the handle is heavy pull it hard. Using your hand attach the hose tightly to the pressure by way of the water inlet which is clearly labeled. Step no 1.

Up to 32 cash back Download or print a free copy of the user manual below. Find the most common problems that can cause a Craftsman Pressure Washer not to work - and the parts instructions to fix them. Right position of craftsman pressure washer matters.

Pin On Products